ASAHI Net : Internet Software Guide

WEB MAIL / SITE MAP / JAPANESE
Internet Service Provider in Japan - English Signup and English Customer Service

Support > Configuration Guide > FlashWave 2040 M1 Configuration

FlashWave 2040 M1 Configuration.

I. Before making the configuration, ensure that...

1. Have you received notification of the opening date of this service?
You should have received notification by email, sent to the email address you supplied when completing your application for the ADSL service, of the date on which the ADSL service will be opened on your line. If you attempt this configuration before the ADSL service has been opened, you will not be able to connect to the ADSL service.

2. Do you know your ADSL connection ID?
To connect to this ADSL service, you need to use your ASAHI Net User ID and password, as follows.

User Name ASAHI Net User ID@atson.net

Password ASAHI Net password

3. Prepare for connection.
There is no software to be installed as part of this configuration. Connect a length of "straight" Ethernet cable (supplied with the ADSL modem) between the FlashWave 2040 ADSL modem's Ethernet 10M/100M port and your computer's LAN card.

Type 1 line: ADSL and voice call capability on the same line
(Click here for schematic)
Connect a length of modular cable (supplied with the ADSL modem) between your wall jack and the LINE jack of the splitter (supplied with the ADSL modem). Connect another length of modular cable (supplied with the ADSL modem) between the MODEM jack of the splitter and the ADSL jack of the ADSL modem.

Type 2 line: ADSL-only line
(Click here for schematic)
Connect a length of modular cable (supplied with the ADSL modem) between your wall jack and the ADSL jack of the ADSL modem.

With both computer and ADSL modem turned on, you will want to see the POWER, ADSL, and Ethernet lamps of the ADSL modem fully lit (not off or flashing).

More information about the setup can be found in the documentation supplied with the ADSL modem.

II. Configuration.

Open the setup page

1. Open a Web browser (Internet Explorer, for example). You must not connect to the Internet: you are going to use the Web browser as the means to open up the configuration page of the FlashWave 2040 M1 ADSL modem.

2. Enter 192.168.0.1 in the Address box of the Web broswer, then hit the Enter key on your keyboard.

3. The following button will appear. Click it.

Enter the Administration password

4. At this point, the Enter Network Password window will appear. Enter admin in lower case characters in both the User Name and Password boxes.

Click the OK button.

Router/Bridge mode set-up screen

5. The Router/Bridge mode set-up screen will appear. Enter the following settings into the boxes in the set-up screen.

a.)	ADSL Saabisu Sentaku (choose ADSL service)	3 ISP3, VPI=0, VCI=35, Ru-tamo-do(PPPoE)Setsuzoku. As shown in the example below. WARNING: Do not choose a different option because it will become impossible to access the ADSL modem again.
b.)	Roguin Yuuza ID (login user name)	Enter your ASAHI Net User ID@atson.net Eg. ab4t-ash@atson.net
c.)	Roguin Pasuwaado (login password)	Enter your ASAHI Net password.
d.)	Pasuwaado no Kakunin (password confirmation)	Re-enter your ASAHI Net password.
e.)	Ninshouhoushikisettei (authentication setting)	PAP
f.)	Jidousetsuzoku (automatic connection)	YuuKou (enable)
g.)	Mutsuushin Kanshi Jikan (period recognized as no communication)	0

6. Click the h.) Setsuzoku (connect) button; it is the middle of the three grey buttons.

Router/Bridge mode set-up screen - 1

7. If the a.) Setsuzoku joutai (connection status) is b.) setsuzokuchuu (connecting) then your ADSL modem is attempting to connect to the Internet.

Click the OK button.

Router/Bridge mode set-up screen - 2

8. The following window will appear to request the re-start of your ADSL modem.

Make sure the top of the two radio buttons Tadachi ni... (immediately save these settings and restart the ADSL modem) is selected.

Click the OK button.

Restart computer

9. After about 10 seconds, a message will appear asking you to wait a little longer.

10. After about 40 seconds, the following button will appear, asking you to click it. Click the button.

Please do not turn off your ADSL modem.

11. Once your ADSL modem has restarted, you should be able to see a.) Setsuzoku joutai (connection status) is still b.) setsuzokuchuu (connecting) in the settings window, showing that the modem is connected to ASAHI Net.

Check the configuration again

12. Below is the correct status of the lamps on the ADSL modem after connection has been established.

13. Your computer should now be connected to the Internet. Open a Web browser (e.g. Internet Explorer) and make sure that you can view Web pages and use other Internet services such as email.